「哈爾濱硬質快速門」快速門常見故障處理方法


Treatment of Common Faults of Hard Fast Gate

根據硬質快速門廠家多年的經驗來看，一般硬質快速門發現故障主要是如下幾方面的問題造成的結果。


According to the experience of hard fast door manufacturers for many years, the failure of hard fast door is mainly caused by the following problems.


硬質快速門的制動打滑，手拉鏈條拉不動，硬質快速門自重下落的失效，電機不啟動。


The brake of the hard fast door is slippery, the hand zipper can not be pulled, the self-weight of the hard fast door falls out of effect, and the motor does not start.

當硬質快速門制動打滑的時代，用汽油清洗門制動摩剎片上的油污;因壓縮彈簧的壓力減少更換彈簧;重新的將電磁鐵安裝到正確的位置上。


In the era of rigid fast door braking slippage, gasoline is used to clean the oil stain on the brake pad of the door brake; the spring is replaced because the pressure of the compression spring decreases; and the electromagnet is re-installed in the correct position.


當硬質快速門的手拉鏈填拉不動的時代，將鏈條理順，由于環繞的鏈條可能會堵住十字的槽;若電磁鐵緊固件松動了重新的緊固好。


When the hand zipper of the hard fast door can not be filled and pulled, straighten out the chain, because the surrounding chain may block the cross slot; if the electromagnet fastener is loose and re-fastened well.


如果是硬質快速門自重下落的失效，更換手動的拉桿，由于硬質快速門的手動拉桿變形;減小手動拉桿與墊圈之間的間隙;如果是由于齒輪箱的電機潤滑失效了，就會更換油脂了。


If the weight of the hard fast door fails to fall, replace the manual pull rod, because of the deformation of the manual pull rod of the hard fast door; reduce the gap between the manual pull rod and washer; if the motor lubrication of the gearbox fails, the grease will be replaced.


當電機不起動的時代，可以從這幾方面排查故障。


When the motor does not start, we can troubleshoot from these aspects.


「哈爾濱硬質快速門」快速門常見故障處理方法


Treatment of Common Faults of Hard Fast Gate


將電路斷開，檢查電線;


Disconnect the circuit and check the wires.


檢查運轉的電容，如損了就壞即更換;


Check the running capacitance and replace it if it is damaged.
 

檢查電機的過熱保護器，一旦過熱保護失效就更換;


Check the motor's overheat protector and replace it once the overheat protection fails.


制動器受粘的處理方法是手動鏈條的拉動轉幾下;


The method of dealing with sticky brake is to pull and turn the manual chain several times.


當發現了限位開關常閉的觸點不通的時代，要更換限位開關跟打磨觸點是一個正確的選擇喲;


When it is found that the contacts of the limit switch are not open, it is a correct choice to replace the limit switch and polish the contacts.


如果是繼電器線圈壞了或者是氧化壞了，沾污的話，處理的方法則是更換繼電器或者是將觸點打磨好;


If the relay coil is damaged or oxidized or contaminated, the treatment method is to replace the relay or grind the contacts well.


將電機的溫度下降，當電機由于運行的時間過于長，熱保護斷開而造成的不起動的情況;


When the temperature of the motor decreases, the motor will not start because of the long running time and the disconnection of the thermal protection.


更換橋式整流器、電磁線圈當橋式整流器壞了或者是制動器卡死，電線圈壞了的時代。


Replacement of bridge rectifier and electromagnetic coil when bridge rectifier is broken or brake is jammed and electric coil is broken.


總的說來，硬質快速門發現故障的原因有可能錯綜復雜的，不過了解一下發現故障的原因也是有備無患的喲。


Generally speaking, the reasons for finding faults in hard fast doors may be complicated, but it is also safe to know the reasons for finding faults.


當發現故障如果您自行不能維修的話就的找專科人士進行維修了，避免自己的不正當操作，對硬質快速門造成更大的傷害喲。


If you find fault, if you can't repair it by yourself, go to a specialist to repair it. Avoid improper operation and cause more damage to the hard fast door.